Menü Schließen
SuperArc XLS

Durchmesser / Lieferform

Durchmesser
 44 lb Spool
 1000 lb Accu-Pak® Box
1,0 mm (0,040 in) ED037829
1,1 mm (0,045 in) ED037698
1,2 mm (0,047 in) ED037556 ED037555

SuperArc® XLS

MIG/MAG Schweißen (GMAW)

KLASSIFIZIERUNGEN::
ISO 14341-A : G 42 3 M20 Z

Durchmesser

Durchmesser wählen

  • 1,0 mm (0,040 in)
  • 1,1 mm (0,045 in)
  • 1,2 mm (0,047 in)

Lieferform

Lieferform auswählen

  • 44 lb Spool
  • 1000 lb Accu-Pak® Box

DETAILS

Eigenschaften

  • Minimize surface silicates for exceptionally clean weld surface
  • Reduced silicates for improved paint adhesion and increased corrosion resistance
  • Microguard® Ultra surface treatment for consistent, stable arc performance with little to no weld spatter
  • Optimized for use with Rapid X® LS mode to lower silicate island formation and spatter generation

Typische Anwendungen

  • Fillet and lap welds on thin material, including but not limited to automotive frames, chassis and suspension components
  • Designed specifically for high speed, single pass applications

Schweißpositionen

  • Flat/Horizontal

Schutzgas

  • Mixed Shielding Gas

Service Informationen

BEFORE USE, READ AND UNDERSTAND THE SAFETY DATA SHEET (SDS) FOR THIS PRODUCT AND SPECIFIC INFORMATION PRINTED ON THE PRODUCT CONTAINER. SDS-Suchseite

CONFORMANCE

CONFORMANCES SPECIFICATION CLASSIFICATION
ISO ISO 14341-A G 42 3 M20 Z

MECHANICAL PROPERTIES

Classification Shielding Gas Polarity Yield Strength @ 0.2% Offset
MPa (ksi) 		Tensile Strength
MPa (ksi) 		Elongation
% 		Charpy V-Notch
J (ft-lbs) @ -30°C (-20°F)
G 42 3 M20 Z Requirement M20 Info. Only 420 (61) min. 500-640 (72-93) 20 min. 47 (35) min.
Typical Result, As-welded 90% Ar, 10% CO2 DC+ 440 (64) 530 (77) 24 102-184 (75-136)

WIRE COMPOSITION

Classification %Al %C %Cr %Mn %Mo %Ni %P %S %Si %Total Cu %V %Ti+Zr
Typical Result 0.02 0.07 0.02 1.68 0.00 max. 0.27 0.004 0.004 0.05 0.17 0.01 0.09

TYPICAL OPERATING PROCEDURES

Diameter Transfer Mode Shielding Gas Polarity CTWD
mm (in.) 		Wire Feed Speed
m/min (in/min) 		Voltage
volts 		Approx. Current
amps 		Melt-off Rate
kg/hr (lb/hr)
1.2 mm (3/64") Spray Transfer 80% Ar, 20% CO2 DC+ 19 (³/₄) 3.8 (150) 24 120 2.0 (4.5)
1.2 mm (3/64") Spray Transfer 80% Ar, 20% CO2 DC+ 19 (³/₄) 8.9 (350) 29 265 4.7 (10.3)
1.2 mm (3/64") Spray Transfer 80% Ar, 20% CO2 DC+ 19 (³/₄) 14.0 (550) 32 370 7.3 (16.2)
1.2 mm (3/64") Spray Transfer 90% Ar, 10% CO2 DC+ 19 (³/₄) 3.8 (150) 23 125 2.0 (4.5)
1.2 mm (3/64") Spray Transfer 90% Ar, 10% CO2 DC+ 19 (³/₄) 8.9 (350) 28 255 4.7 (10.4)
1.2 mm (3/64") Spray Transfer 90% Ar, 10% CO2 DC+ 19 (³/₄) 14.0 (550) 32 360 7.3 (16.0)
.040" (1.0 mm) Spray Transfer 80% Ar, 20% CO2 DC+ 16 (⁵/₈) 5.6 (220) 23 105 2.1 (4.6)
.040" (1.0 mm) Spray Transfer 80% Ar, 20% CO2 DC+ 16 (⁵/₈) 8.9 (350) 26 170 3.3 (7.3)
.040" (1.0 mm) Spray Transfer 80% Ar, 20% CO2 DC+ 16 (⁵/₈) 11.4 (450) 28 210 4.2 (9.3)
.040" (1.0 mm) Spray Transfer 80% Ar, 20% CO2 DC+ 16 (⁵/₈) 15.2 (600) 30 260 5.9 (13.1)
.040" (1.0 mm) Spray Transfer 90% Ar, 10% CO2 DC+ 16 (⁵/₈) 5.6 (220) 22 105 2.2 (4.8)
.040" (1.0 mm) Spray Transfer 90% Ar, 10% CO2 DC+ 16 (⁵/₈) 8.9 (350) 25 170 3.3 (7.3)
.040" (1.0 mm) Spray Transfer 90% Ar, 10% CO2 DC+ 16 (⁵/₈) 11.4 (450) 27 210 4.2 (9.3)
.040" (1.0 mm) Spray Transfer 90% Ar, 10% CO2 DC+ 16 (⁵/₈) 15.2 (600) 29 260 5.7 (12.6)
.035" (0.9 mm) Spray Transfer 80% Ar, 20% CO2 DC+ 16 (⁵/₈) 6.4 (250) 23 100 1.9 (4.1)
.035" (0.9 mm) Spray Transfer 80% Ar, 20% CO2 DC+ 16 (⁵/₈) 8.9 (350) 25 140 2.6 (5.8)
.035" (0.9 mm) Spray Transfer 80% Ar, 20% CO2 DC+ 16 (⁵/₈) 12.7 (500) 27 180 3.9 (8.5)
.035" (0.9 mm) Spray Transfer 80% Ar, 20% CO2 DC+ 16 (⁵/₈) 16.5 (650) 29 220 5.1 (11.3)
.035" (0.9 mm) Spray Transfer 90% Ar, 10% CO2 DC+ 16 (⁵/₈) 6.4 (250) 24 100 1.9 (4.2)
.035" (0.9 mm) Spray Transfer 90% Ar, 10% CO2 DC+ 16 (⁵/₈) 8.9 (350) 26 140 2.6 (5.8)
.035" (0.9 mm) Spray Transfer 90% Ar, 10% CO2 DC+ 16 (⁵/₈) 12.7 (500) 28 180 3.9 (8.5)
.035" (0.9 mm) Spray Transfer 90% Ar, 10% CO2 DC+ 16 (⁵/₈) 16.5 (650) 30 220 4.9 (10.9)