Menu Close
10 Pound Cans of Stick Electrode

Diameters / Packaging

Diameters
 (3) 10 lb Easy Open Can
3.2 x 350 mm (1/8 x 14 in) ED032622
4.0 x 350 mm (5/32 x 14 in) ED032623

Pipeliner® 19P

Stick (SMAW)

AWS:
E10018-G H4R

Low Alloy, Low Hydrogen, Pipe • AWS E10018-G H4R

Diamètre

Sélectionnez le diamètre

  • 3.2 x 350 mm (1/8 x 14 in)
  • 4.0 x 350 mm (5/32 x 14 in)

Paquet

Sélectionnez un forfait

  • (3) 10 lb Easy Open Can
Acheter maintenant

Détails

Traits

  • Charpy V-Notch impact toughness tested to -46°C (-50°F)

Applications typiques

  • Fill and cap pass welding of up to X80 grade pipe
  • Low hydrogen, vertical up capability on X80 grade pipe

Positions de soudage

  • All except vertical down

Gaz de protection

  • Not Applicable

Caractéristiques spéciales

  • Q2 Lot® - Control and Tested - Lot certificate available online

Disclaimers

Warning -

Cancer and Reproductive Harm -

www.P65Warnings.ca.gov

Des informations de service

Vous pourriez également avoir besoin

50 lb Can of Lincoln Electric Stick Electrodes

Excalibur® 11018M MR® Stick (SMAW) Electrode

ED031975
50 lb Can of Lincoln Electric Stick Electrodes

Excalibur® 11018M MR® Stick (SMAW) Electrode

ED031976
50 lb Can of Lincoln Electric Stick Electrodes

Excalibur® 11018M MR® Stick (SMAW) Electrode

ED031977
50 lb Can of Lincoln Electric Stick Electrodes

Excalibur® 11018M MR® Stick (SMAW) Electrode

ED031978
Voir tout

BEFORE USE, READ AND UNDERSTAND THE SAFETY DATA SHEET (SDS) FOR THIS PRODUCT AND SPECIFIC INFORMATION PRINTED ON THE PRODUCT CONTAINER. SDS Search page

See test result disclaimer

CONFORMANCE

CONFORMANCES SPECIFICATION CLASSIFICATION
AWS AWS A5.5 E10018-G-H4R

MECHANICAL PROPERTIES

Classification Yield Strength @ 0.2% Offset
MPa (ksi) 		Tensile Strength
MPa (ksi) 		Elongation
% 		Charpy V-Notch
J (ft-lbs) @ -45°C (-50°F)
E10018-G-H4R Requirement 600 (87) min. 690 (100) min. 16 min.
Typical Result, As-welded 660-750 (95-109) 730-800 (106-115) 21-28 73-125 (54-92)

DEPOSIT COMPOSITION

Classification %B %C %Cr %Cu %Mn %Mo %Ni %P %S %Si %V Diffusible Hydrogen
mL/100g Weld Metal 		1800F H2O - As received 1800F H2O - After 9 hrs at 80F/80%RH
E10018-G-H4R Requirement 0.30 min. * 0.20 min. * 1.00 min. * 0.20 min. * 0.50 min. * 0.03 max. 0.03 max. 0.80 min. * 0.10 min. * 4 max. 0.15 max. 0.4 max.
Typical Result 0.0002 max. 0.038-0.049 0.02-0.04 0.01-0.07 1.54-1.89 0.42-0.45 2.06-2.28 0.01 0.01 0.40-0.54 0.01 max. 1-3 0.02-0.10 0.1-0.3

TYPICAL OPERATING PROCEDURES

Diameter Polarity⁽¹⁾ Current
Amps
3.2 mm (1/8 in) DC+ 80-155
3.2 mm (1/8 in) AC 80-160
4.0 mm (5/32 in) DC+ 130-210
4.0 mm (5/32 in) AC 140-215

NOTES

Note
* To meet the requirements of a "G" classification, the chemical composition of the weld deposit must meet the minimum requirement for one or more of these elements.
⁽¹⁾ Preferred polarity is listed first.