Détails
Designed for vertical down welding of cross-country and in-plant pipe
Traits
- High operator appeal and control
- Easy slag removal
- Standard in the pipe welding industry
- Meets NACE MR0175 for sour gas applications
- Test data available for SSC (NACE TM0177) & HIC (NACE TM0284)
Applications typiques
- Cross country and in-plant pipe welding
- Root pass on up to X80 grade pipe
- Hot, fill and cap pass on up to X60 grade pipe
Positions de soudage
- All
Gaz de protection
- Not Applicable
Caractéristiques spéciales
- Q2 Lot® - Lot Controlled Chemistry and Mechanical Properties
Disclaimers
Des informations de service
Vous pourriez également avoir besoin
BEFORE USE, READ AND UNDERSTAND THE SAFETY DATA SHEET (SDS) FOR THIS PRODUCT AND SPECIFIC INFORMATION PRINTED ON THE PRODUCT CONTAINER. SDS Search page
See test result disclaimer
CONFORMANCE
| CONFORMANCES | SPECIFICATION | CLASSIFICATION |
|---|---|---|
| AWS | AWS A5.1 | E6010 |
| ISO | ISO 2560-A | E 42 3 C 2 1 |
| ABS | AWS A5.1 | E6010 |
| CWB | CSA W48 | E4310 |
| DNV-GL | DNV - 2.9 | 3 |
| CONFORMANCES | SPECIFICATION | CLASSIFICATION |
|---|---|---|
| AWS | AWS A5.1 | E6010 |
| ISO | ISO 2560-A | E 42 3 C 2 1 |
| ABS | AWS A5.1 | E6010 |
| CWB | CSA W48 | E4310 |
| DNV-GL | DNV - 2.9 | 3 |
MECHANICAL PROPERTIES
| Classification |
Yield Strength @ 0.2% Offset
MPa (ksi) |
Tensile Strength
MPa (ksi) |
Elongation
% |
Charpy V-Notch
J (ft-lbs) @ -30°C (-20°F) |
Hardness Rockwell B |
|---|---|---|---|---|---|
| E6010 Requirement | 330 (48) min. | 410 (60) min. | 22 min. | 27 (20) min. | |
| Typical Result, As-welded | 400-560 (59-81) | 490-670 (72-98) | 22-33 | 29-113 (21-83) | 84-86 |
| Classification |
Yield Strength @ 0.2% Offset
MPa (ksi) |
Tensile Strength
MPa (ksi) |
Elongation
% |
Charpy V-Notch
J (ft-lbs) @ -30°C (-20°F) |
Hardness Rockwell B |
|---|---|---|---|---|---|
| E6010 Requirement | 330 (48) min. | 410 (60) min. | 22 min. | 27 (20) min. | |
| Typical Result, As-welded | 400-560 (59-81) | 490-670 (72-98) | 22-33 | 29-113 (21-83) | 84-86 |
DEPOSIT COMPOSITION
| Classification | %C | %Cr | %Mn | %Mo | %Ni | %P | %S | %Si | %V |
|---|---|---|---|---|---|---|---|---|---|
| E6010 Requirement | 0.20 max. | 0.20 max. | 1.20 max. | 0.30 max. | 0.30 max. | 1.00 max. | 0.08 max. | ||
| Typical Result | 0.10-0.20 | 0.01-0.04 | 0.43-0.73 | 0.03 max. | 0.07 max. | 0.003-0.012 | 0.003-0.014 | 0.12-0.30 | 0.01 max. |
| Classification | %C | %Cr | %Mn | %Mo | %Ni | %P | %S | %Si | %V |
|---|---|---|---|---|---|---|---|---|---|
| E6010 Requirement | 0.20 max. | 0.20 max. | 1.20 max. | 0.30 max. | 0.30 max. | 1.00 max. | 0.08 max. | ||
| Typical Result | 0.10-0.20 | 0.01-0.04 | 0.43-0.73 | 0.03 max. | 0.07 max. | 0.003-0.012 | 0.003-0.014 | 0.12-0.30 | 0.01 max. |
TYPICAL OPERATING PROCEDURES
| Diameter | Polarity⁽¹⁾ |
Current
Amps |
|---|---|---|
| 2.5 mm (3/32 in) | DC+ | 50-85 |
| 2.5 mm (3/32 in) | DC- | 50-85 |
| 3.2 mm (1/8 in) | DC+ | 75-135 |
| 3.2 mm (1/8 in) | DC- | 75-135 |
| 4.0 mm (5/32 in) | DC+ | 100-175 |
| 4.0 mm (5/32 in) | DC- | 100-175 |
| Diameter | Polarity⁽¹⁾ |
Current
Amps |
|---|---|---|
| 2.5 mm (3/32 in) | DC+ | 50-85 |
| 2.5 mm (3/32 in) | DC- | 50-85 |
| 3.2 mm (1/8 in) | DC+ | 75-135 |
| 3.2 mm (1/8 in) | DC- | 75-135 |
| 4.0 mm (5/32 in) | DC+ | 100-175 |
| 4.0 mm (5/32 in) | DC- | 100-175 |
NOTES
| Note |
|---|
| ⁽¹⁾ Preferred polarity is listed first. |