Diamètres / Emballages

Diamètres	44 lb Spool	1000 lb Accu-Pak® Box
1,0 mm (0,040 in)	ED037829
1,1 mm (0,045 in)	ED037698
1,2 mm (0,047 in)	ED037556	ED037555

SuperArc® XLS

Soudage MIG/MAG (GMAW)

CLASSIFICATION:
AWS A5.18 : ER70S-9
EN ISO 14341-A : G 42 3 M20 Z

Mild Steel, Copper Coated MIG wire

Quels sont les partenaires commerciaux de Lincoln Electric?

S'identifier pour consulter les prix

DÉTAILS

Caractéristiques

Minimize surface silicates for exceptionally clean weld surface
Reduced silicates for improved paint adhesion and increased corrosion resistance
Microguard® Ultra surface treatment for consistent, stable arc performance with little to no weld spatter
Optimized for use with Rapid X® LS mode to lower silicate island formation and spatter generation

Exemples d'applications

Fillet and lap welds on thin material, including but not limited to automotive frames, chassis and suspension components
Designed specifically for high speed, single pass applications

Positions de soudage

Flat/Horizontal

Gaz de protection

M21 : Mixed gas Ar+ 15-25% CO2, M20 : Mixed gas Ar+ 5-15% CO2

Service d'information

BEFORE USE, READ AND UNDERSTAND THE SAFETY DATA SHEET (SDS) FOR THIS PRODUCT AND SPECIFIC INFORMATION PRINTED ON THE PRODUCT CONTAINER. Page de recherche SDS

CONFORMANCE

CONFORMANCES	SPECIFICATION	CLASSIFICATION
ISO	ISO 14341-A	G 42 3 M20 Z

MECHANICAL PROPERTIES

Classification	Shielding Gas	Polarity	Yield Strength @ 0.2% Offset MPa (ksi)	Tensile Strength MPa (ksi)	Elongation %	Charpy V-Notch J (ft-lbs) @ -30°C (-20°F)
G 42 3 M20 Z Requirement	M20	Info. Only	420 (61) min.	500-640 (72-93)	20 min.	47 (35) min.
Typical Result, As-welded	90% Ar, 10% CO2	DC+	440 (64)	530 (77)	24	102-184 (75-136)

WIRE COMPOSITION

Classification	%Al	%C	%Cr	%Mn	%Mo	%Ni	%P	%S	%Si	%Total Cu	%V	%Ti+Zr
Typical Result	0.02	0.07	0.02	1.68	0.00 max.	0.27	0.004	0.004	0.05	0.17	0.01	0.09

TYPICAL OPERATING PROCEDURES

Diameter	Transfer Mode	Shielding Gas	Polarity	CTWD mm (in.)	Wire Feed Speed m/min (in/min)	Voltage volts	Approx. Current amps	Melt-off Rate kg/hr (lb/hr)
1.2 mm (3/64")	Spray Transfer	80% Ar, 20% CO2	DC+	19 (³/₄)	3.8 (150)	24	120	2.0 (4.5)
1.2 mm (3/64")	Spray Transfer	80% Ar, 20% CO2	DC+	19 (³/₄)	8.9 (350)	29	265	4.7 (10.3)
1.2 mm (3/64")	Spray Transfer	80% Ar, 20% CO2	DC+	19 (³/₄)	14.0 (550)	32	370	7.3 (16.2)
1.2 mm (3/64")	Spray Transfer	90% Ar, 10% CO2	DC+	19 (³/₄)	3.8 (150)	23	125	2.0 (4.5)
1.2 mm (3/64")	Spray Transfer	90% Ar, 10% CO2	DC+	19 (³/₄)	8.9 (350)	28	255	4.7 (10.4)
1.2 mm (3/64")	Spray Transfer	90% Ar, 10% CO2	DC+	19 (³/₄)	14.0 (550)	32	360	7.3 (16.0)
.040" (1.0 mm)	Spray Transfer	80% Ar, 20% CO2	DC+	16 (⁵/₈)	5.6 (220)	23	105	2.1 (4.6)
.040" (1.0 mm)	Spray Transfer	80% Ar, 20% CO2	DC+	16 (⁵/₈)	8.9 (350)	26	170	3.3 (7.3)
.040" (1.0 mm)	Spray Transfer	80% Ar, 20% CO2	DC+	16 (⁵/₈)	11.4 (450)	28	210	4.2 (9.3)
.040" (1.0 mm)	Spray Transfer	80% Ar, 20% CO2	DC+	16 (⁵/₈)	15.2 (600)	30	260	5.9 (13.1)
.040" (1.0 mm)	Spray Transfer	90% Ar, 10% CO2	DC+	16 (⁵/₈)	5.6 (220)	22	105	2.2 (4.8)
.040" (1.0 mm)	Spray Transfer	90% Ar, 10% CO2	DC+	16 (⁵/₈)	8.9 (350)	25	170	3.3 (7.3)
.040" (1.0 mm)	Spray Transfer	90% Ar, 10% CO2	DC+	16 (⁵/₈)	11.4 (450)	27	210	4.2 (9.3)
.040" (1.0 mm)	Spray Transfer	90% Ar, 10% CO2	DC+	16 (⁵/₈)	15.2 (600)	29	260	5.7 (12.6)
.035" (0.9 mm)	Spray Transfer	80% Ar, 20% CO2	DC+	16 (⁵/₈)	6.4 (250)	23	100	1.9 (4.1)
.035" (0.9 mm)	Spray Transfer	80% Ar, 20% CO2	DC+	16 (⁵/₈)	8.9 (350)	25	140	2.6 (5.8)
.035" (0.9 mm)	Spray Transfer	80% Ar, 20% CO2	DC+	16 (⁵/₈)	12.7 (500)	27	180	3.9 (8.5)
.035" (0.9 mm)	Spray Transfer	80% Ar, 20% CO2	DC+	16 (⁵/₈)	16.5 (650)	29	220	5.1 (11.3)
.035" (0.9 mm)	Spray Transfer	90% Ar, 10% CO2	DC+	16 (⁵/₈)	6.4 (250)	24	100	1.9 (4.2)
.035" (0.9 mm)	Spray Transfer	90% Ar, 10% CO2	DC+	16 (⁵/₈)	8.9 (350)	26	140	2.6 (5.8)
.035" (0.9 mm)	Spray Transfer	90% Ar, 10% CO2	DC+	16 (⁵/₈)	12.7 (500)	28	180	3.9 (8.5)
.035" (0.9 mm)	Spray Transfer	90% Ar, 10% CO2	DC+	16 (⁵/₈)	16.5 (650)	30	220	4.9 (10.9)