DETALII
The choice for novice or experienced welders looking for an easy to operate self-shielded, flux-cored wire. The excellent arc control and accommodating weld puddle enable operators to make high quality weld deposits regardless of skill level.
Caracteristici
- Capacitate de alimentare imbunatatita - Noul design mareste rigiditatea sarmei pentru a ajuta la avansul sarmei si promoveaza transferul lin al arcului
- Ruperea sarmei - Capatul sarmei poate fi rupt cu usurinta fara a fi nevoie de sculespecializate
- Indeplineste cerintele AWS D1.8 pentru sudurile critice - Trei loturi testate privind testele AWS D1.8 le gasiti la adresa www.lincolnelectric.com/D1.8
- Operabilitate fara efort - Sudorii din toate nivelurile de calificare beneficieaza de un arc usor de controlat si o baia de metal topit foarte permisiva chiar si la sudarea pozitionala.
Informații despre service
Documentație
S-ar putea să aveți nevoie și de
BEFORE USE, READ AND UNDERSTAND THE SAFETY DATA SHEET (SDS) FOR THIS PRODUCT AND SPECIFIC INFORMATION PRINTED ON THE PRODUCT CONTAINER. Pagina de căutare FDS
CONFORMANCE
| CONFORMANCES | SPECIFICATION | CLASSIFICATION |
|---|---|---|
| AWS | AWS A5.20 | E71T-8-H8 |
| AWS | AWS A5.36 | E71T8-A2-CS3-H8 |
| ABS | ABS - Part 2 | 3YSA |
MECHANICAL PROPERTIES
| Classification | Polarity |
Yield Strength @ 0.2% Offset
MPa (ksi) |
Tensile Strength
MPa (ksi) |
Elongation
% |
Charpy V-Notch
J (ft-lbs) @ -30°C (-20°F) |
|---|---|---|---|---|---|
| E71T-8-H8 Requirement | DC- | 400 (58) min. | 480-660 (70-95) | 22 min. | 27 (20) min. |
| E71T8-A2-CS3-H8 Requirement | DC- | 400 (58) min. | 480-660 (70-95) | 22 min. | 27 (20) min. |
| Typical Result, As-welded | DC- | 430 (62) | 560-610 (81-88) | 25 | 41-75 (30-55) |
DEPOSIT COMPOSITION
| Classification | Polarity | %Al | %B | %C | %Mn | %P | %S | %Si |
Diffusible Hydrogen
mL/100g Weld Metal |
|---|---|---|---|---|---|---|---|---|---|
| E71T-8-H8 Requirement | DC- | 0.30 max. | 1.75 max. | 0.03 max. | 0.03 max. | 0.60 max. | 8.0 max. | ||
| E71T8-A2-CS3-H8 Requirement | DC- | 0.30 max. | 1.75 max. | 0.030 max. | 0.030 max. | 0.60 max. | 8 max. | ||
| Typical Result | DC- | 0.6-0.8 | 0.0017 | 0.16-0.20 | 0.58-0.69 | 0.011 | 0.010 | 0.18-0.24 | 5.5 |
TYPICAL OPERATING PROCEDURES
| Diameter | Polarity |
CTWD
mm (in.)⁽¹⁾ |
Wire Feed Speed
m/min (in/min) |
Voltage
volts |
Approx. Current
amps |
Melt-off Rate
kg/hr (lb/hr) |
Deposition Rate
kg/hr (lb/hr) |
Efficiency
% |
|---|---|---|---|---|---|---|---|---|
| 1/16 in (1.6 mm) | DC- | 25 (1) | 3.8 (150) | 17-19 | 220 | 2.4 (5.3) | 1.9 (4.2) | 80 |
| 1/16 in (1.6 mm) | DC- | 25 (1) | 5.1 (200) | 19-21 | 245 | 3.2 (7.1) | 2.5 (5.4) | 76 |
| 1/16 in (1.6 mm) | DC- | 25 (1) | 6.4 (250) | 21-23 | 270 | 4.0 (8.9) | 3.0 (6.6) | 74 |
| 1/16 in (1.6 mm) | DC- | 25 (1) | 7.6 (300) | 23-25 | 295 | 4.7 (10.4) | 3.5 (7.7) | 75 |
| 1/16 in (1.6 mm) | DC- | 25 (1) | 8.9 (350) | 25-27 | 315 | 5.6 (12.3) | 4.3 (9.4) | 77 |
| 0.072 in (1.8 mm) | DC- | 19-25 (3/4-1) | 2.5 (100) | 17-18 | 184 | 2.0 (4.5) | 1.6 (3.6) | 80 |
| 0.072 in (1.8 mm) | DC- | 19-25 (3/4-1) | 3.8 (150) | 18-19 | 250 | 3.1 (6.7) | 2.5 (5.4) | 80 |
| 0.072 in (1.8 mm) | DC- | 19-25 (3/4-1) | 5.1 (200) | 20-21 | 295 | 4.0 (8.9) | 3.2 (7.1) | 81 |
| 0.072 in (1.8 mm) | DC- | 19-25 (3/4-1) | 6.4 (250) | 22-23 | 330 | 5.1 (11.2) | 4.0 (8.9) | 79 |
| 0.072 in (1.8 mm) | DC- | 19-25 (3/4-1) | 7.6 (300) | 23-24 | 355 | 6.1 (13.4) | 4.8 (10.6) | 79 |
| 5/64 in (2.0 mm) | DC- | 19-25 (3/4-1) | 2.3 (90) | 18-19 | 210 | 2.2 (4.9) | 1.8 (4.1) | 82 |
| 5/64 in (2.0 mm) | DC- | 19-25 (3/4-1) | 3.2 (125) | 19-20 | 260 | 3.2 (7.0) | 2.6 (5.6) | 81 |
| 5/64 in (2.0 mm) | DC- | 19-25 (3/4-1) | 3.8 (150) | 20-21 | 300 | 3.8 (8.4) | 3.0 (6.7) | 80 |
| 5/64 in (2.0 mm) | DC- | 19-25 (3/4-1) | 5.1 (200) | 21-22 | 340 | 5.1 (11.2) | 4.1 (9.0) | 81 |
| 5/64 in (2.0 mm) | DC- | 19-25 (3/4-1) | 6.1 (240) | 22-23 | 380 | 6.1 (13.3) | 4.9 (10.8) | 81 |
NOTES
| Note |
|---|
| ⁽¹⁾ CTWD for 0.072 in. (1.8 mm) and 5/64 in. (2.0 mm) for 200 ipm or greater is 1 in (25 mm) |